Home > Heaters > Forced Air Heaters > Electric Forced Air Heaters >

Fan Forced Horizontal Discharge Unit Heater P3PUH20CA1

Fan Forced Horizontal Discharge Unit Heater P3PUH20CA1
Fan Forced Horizontal Discharge Unit Heater P3PUH20CA1
SKU: P3PUH20CA1
Manufacturer: TPI Corporation Heaters
BTU /hr.:
68300 btu's
Fuel Type:
Electric
Dimensions:
24"W x 17"D x 17"H
Voltage:
480 V

HeaterStore or any of it's affliates are not responsible for damages or injury caused by wrongful installation or application of this product.


Availability: Out of Stock
notify me
Retail: $2,991.00 Price: $1,645.05 You Save: $1,345.95 (45.0%)
 




    Description

    The affordable way to keep things warm with this 20 KW Fan Forced Horizontal Discharge Unit Heater made by TPI. Model P3PUH20CA1 is efficiently gives 68300 BTU output. This model has circular copper clad steel element with continuously brazed steel fins formed to match the air delivery pattern of the fan blade. This ETL listed unit has linear limit type thermal overload with automatic reset. This unit makes less noise with its sleeve bearings mounted with rubber insulators.

    TPI Fan Forced Horizontal Discharge Unit Heater - P3PUH20CA1 Specifications
    Wattage20 KW
    BTU's68300 BTU
    VOLTS480V
    Phase3 Ph
    AMPS24.1
    Control Voltage24
    Temp Rise deg F47 F
    Air Throw56'
    CFM1350
    Recom'd Mounting Ht.13'
    Dimension24"W x 17"D x 17"H
    Weight55 lbs.
    UPC686334688321
    ListedETL Listed

    Fan Forced Horizontal Discharge Unit Heater - P3PUH20CA1 Features:

    CONSTRUCTION:

    • 18 ga. steel cabinet with powder coated finish and control compartment with a hinged and latched access door, simplifying wiring installation & maintenance

    HEATING ELEMENT:

    • Circular copper clad steel element with continuously brazed steel fins formed to match the air delivery pattern of the fan blade

    OVERHEAT PROTECTION:

    • Equipped with automatic reset type limit controls to de-energize the

    FAN and MOTOR:

    • Heater should an over-temperature situation occur.
    • Sleeve bearings mounted with rubber insulators to minimize vibration and noise
    • Fan assembly enclosed by a heavy gauge, close spaced, chrome plated wire guard.

    LOUVER ASSEMBLY:

    • Louvers are individually adjustable for directional control of air flow and the louver assembly can be repositioned in the field from down air flow to right or left directional air flow.

    TEMPERATURE CONTROLS:

    • 20 KW through 48 KW units and all 480V have built in 24 volt transformer for low voltage remote thermostat application
    • 25 KW through 48 KW models available in 2-stage on special order

    INSTALLATION:

    • UH Series may be mounted at a maximum of 45 degrees off of horizontal
    • On all models up to 15 KW, 1/4" threaded rod may be used for mounting; on all models 20 KW and above 5/16" threaded rod may be used
    • Optional wall / ceiling mounting brackets available for all units
    • Suitable for applications up to 13,000 feet

    FACTORY INSTALLED OPTIONS:

    • 24 volt transformer on 3 KW to 15KW units to convert from line voltage to low voltage remote thermostat operation (non CA1 models only)
    • Summer fan switch to operate the fan only.
    • Fan Delay Switch to purge all residual heat from the unit after the heating element has cycled off
    • Powder coated Epoxy finish is available -
    • Disconnect switch
    Specifications

    TPI Fan Forced Horizontal Discharge Unit Heater P3PUH20CA1 Resources:

    TPI Fan Forced Horizontal Discharge Unit Heater P3PUH20CA1 Specifications
    Dimensions
    24"W x 17"D x 17"H